Before qualifications even come into play, OSHA generally prohibits using a crane to hoist employees at all. Under 1926.1431(a), it’s only allowed when the employer can show that conventional access, a personnel hoist, ladder, stairway, aerial lift, or scaffold, would be more hazardous or isn’t possible given the project’s structural design or the site’s conditions.
Once a lift is justified, OSHA leans on a handful of role-based terms to spell out who does what: qualified person, competent person, certified. The rule uses these terms constantly but doesn’t define them itself. The actual definitions live one section earlier, in 1926.1401, the definitions section for Subpart CC, the broader standard covering cranes and derricks that 1926.1431 sits inside.
There’s no single universal sign-off role under 1926.1431. OSHA assigns different inspections and determinations to different qualified and competent individuals, and which one applies depends on the stage of the operation. Here’s what each term actually means, and specifically where it shows up in the personnel hoisting rule.
What’s covered
- What “qualified person” means, and where it applies
- What “competent person” means, and where it applies
- Qualified riggers and signal persons
- Where “certified” actually applies
- A term 1926.1431 doesn’t use
- FAQ
What “qualified person” means, and where it applies
Under 1926.1401, a qualified person is someone who, by possession of a recognized degree, certificate, or professional standing, or by extensive knowledge, training, and experience, has successfully demonstrated the ability to solve or resolve problems relating to the subject matter, the work, or the project. It’s a credentials-or-demonstrated-ability standard, not a specific license.
In 1926.1431, this is the standard applied to:
- Equipment setup and ground stability. Under 1926.1431(c)(1), the equipment has to sit level, within one percent of grade, on footing a qualified person has determined is sufficiently firm and stable.
- Platform design. Under 1926.1431(e)(1), the platform and its suspension or attachment system have to be designed by a qualified person familiar with structural design.
- Operating platform-mounted controls. Under 1926.1431(k)(7), if the platform has its own controls, the person using them has to be a qualified person.
- Weather and environmental judgment calls. Under 1926.1431(k)(8)(i) and (ii), determining whether wind, weather, or other environmental conditions are safe enough to hoist personnel is specifically a qualified person’s call to make.
What “competent person” means, and where it applies
Under the same section, a competent person is someone capable of identifying existing and predictable hazards in the surroundings or working conditions that are unsanitary, hazardous, or dangerous to employees, and who has the authorization to take prompt corrective measures to eliminate them. The distinction that matters here is authority. A competent person isn’t just able to spot a problem, they have to be able to act on it.
In 1926.1431, this is the standard applied to:
- Trial lift confirmation and inspection. Under 1926.1431(h)(3), a competent person confirms the required safety devices are activated and functioning, and that the trial lift won’t exceed 50% of the equipment’s rated capacity, and under (h)(4), that same person inspects the equipment and platform immediately afterward for any defect the trial lift may have exposed.
- Pre-lift checks before every lift. Under 1926.1431(h)(5), immediately before each personnel lift, a competent person confirms the platform is secure and properly balanced after a few inches of hoist, and separately verifies the hoist ropes, line reeving, and primary attachment are properly set.
- Proof test sign-off. Under 1926.1431(j)(3), a competent person inspects the platform and rigging after the proof test to confirm it passed, and personnel hoisting can’t begin until that determination is made.
Qualified riggers and signal persons
Two more roles come from the general Subpart CC framework rather than from 1926.1431 directly. 1926.1431 describes its own requirements as supplemental to the rest of Subpart CC, meaning these roles apply to a personnel hoisting operation in addition to everything specific to 1431.
OSHA defines a qualified rigger in 1926.1401, as simply a rigger who meets the criteria for a qualified person described above. 1926.1431 doesn’t expressly require a qualified rigger for every personnel hoisting operation. Qualified-rigger requirements elsewhere in Subpart CC apply under specific conditions, most directly under 1926.1425(c), whenever a worker is in the fall zone hooking, unhooking, or guiding a load, or making the initial connection of a load to a structure.
A signal person has a more involved path. Under 1926.1428, a signal person has to demonstrate the required knowledge and practical skill, through an oral or written test and a practical test, and the employer has to document that qualification before the person gives any signals. That assessment has to come from either a qualified evaluator employed by their own employer or an independent third-party qualified evaluator.
Only one of the two actually shows up in 1926.1431’s own text. “Qualified rigger” doesn’t appear anywhere in 1431 itself. Signal person does appear directly: the pre-lift meeting required under 1926.1431(m) has to include the signal person, if one is used, and 1926.1431(k)(9) requires hoisted employees to stay in direct communication with the signal person or the operator throughout the lift.
Where “certified” actually applies
Of all the role-based language in 1926.1431, only one provision uses the word “certified” directly. Under 1926.1431(e)(5), all welding on the platform and its components has to be done by a certified welder familiar with the specific weld grades, types, and materials called for in the design. That’s a specific, named requirement, not a general standard applied throughout the rule the way “qualified” and “competent” are.
Certification shows up in one other place relevant to every personnel hoisting operation, just not inside 1926.1431 itself. Under 1926.1427, the employer has to ensure the crane operator is appropriately trained, certified or licensed, and evaluated, a Subpart CC requirement that applies to crane operation generally, not specifically to personnel hoisting. Certification and the employer’s evaluation of the operator’s actual skills are separate requirements; a certificate alone doesn’t establish that an operator is qualified to run the equipment in its current configuration. OSHA also restricts an operator-in-training from hoisting personnel at all unless they’ve met the applicable certification requirement.
A term 1926.1431 doesn’t use
“Designated person” is a term that shows up elsewhere in OSHA’s construction standards, defined in 1926.32 as equivalent to “authorized person,” someone approved or assigned by the employer to perform a specific duty or be at a specific location. It’s worth mentioning here because it’s easy to assume every OSHA role-based term applies everywhere. It doesn’t. 1926.1431 doesn’t use “designated person” anywhere in its text. The roles it actually assigns responsibility to are qualified person, competent person, and, in the one case above, certified welder.
FAQ
What’s the difference between a qualified person and a competent person under 1926.1431?
A qualified person’s standard is demonstrated ability, through a credential or through extensive knowledge and experience, to solve problems related to the work. A competent person’s standard includes that same ability to recognize hazards, plus the authority to actually take corrective action. In 1926.1431, qualified person governs equipment setup, platform design, and weather judgment calls; competent person governs trial lift, pre-lift checks, and proof test sign-off.
Who has to design a crane man basket’s structure?
A qualified person familiar with structural design, under 1926.1431(e)(1).
Who decides if it’s too windy to hoist personnel?
A qualified person, under 1926.1431(k)(8)(i). Exceeding 20 mph sustained wind or gusts at the platform triggers that required safety determination; it isn’t, by itself, an automatic prohibition on hoisting personnel. If the qualified person determines it isn’t safe, the lift can’t begin, or has to stop if it’s already underway.
Does 1926.1431 require a certified rigger or certified signal person?
Not in those exact terms, and 1926.1431 doesn’t require a qualified rigger for every personnel hoisting operation either. It requires a signal person who meets the qualification requirements in 1926.1428. Qualified-rigger requirements elsewhere in Subpart CC, under 1926.1425(c), apply when a worker is in the fall zone handling the load. The one place 1926.1431 uses “certified” specifically is for welding, under (e)(5).
Does the crane operator need a separate certification for personnel hoisting?
1926.1431 doesn’t add a personnel-hoisting-specific operator certification. The operator still has to meet the general crane operator certification, qualification, or licensing requirements in 1926.1427, which apply to crane operation generally.
Built and documented with the right people signing off
Every Lifting Technologies platform is designed by qualified personnel and welded to certification standards called for under 1926.1431(e), with documentation to back it up. Factory testing and inspection don’t replace the jobsite proof testing required under 1926.1431(j), which still has to happen at each jobsite before hoisting personnel, and again after any repair or modification.
- Read the complete breakdown of OSHA 1926.1431 for the full rule these roles operate under
- See how every platform is load tested, certified, and inspected before it ships
- See what’s on the data plate that documents your platform’s specifications
Talk to our team about a platform built to meet the standard from the ground up.
